How to Replace a Kia Sportage Replacement Key
For a variety of Kia models the key comes with a built-in keyless entry system. The key is usually akin to an electronic remote and can be changed with a new one from an Kia dealer or a locksmith.
Key fobs can stop working for a variety of reasons, such as an empty coin battery, worn buttons, water damage, signal interference and a faulty receiver module. Here are some suggestions to help you get your Kia key fob that is a replacement for the sportage once more.
How to replace a smartkey or remote key?
Whether your Kia is equipped with an intelligent key, remote key push-to-start key, or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is especially when the car displays a message telling that the smart key or remote has a low battery.
Luckily, this is quite simple to do. In order to replace the battery on the key fob, remove the mechanical key from the slit in the back of the key fob. Then break the cover. Inside the key fob will be tiny screws that hold the battery in place. Remove the old battery by unwinding the screw using the help of a small screwdriver. Then insert the new one and close the slit on the key fob.
Test the key fob by pressing the lock/unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now make use of your Kia's hands-free lock/unlock feature when your fingers start to get cold or you have to do some errands in Brandon.
Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a computer which is available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of steel) are not required for programming. If you need to reprogramme your key, it is necessary to note the key code number on the tag for the key code.
How do you replace the battery?
If the Kia key fob does not respond to pressing the lock or unlock button, it is most likely that the battery is low. A low battery may cause other issues, like the check engine light turning on or the engine not running correctly. Fortunately replacing the battery on the key fob is a simple DIY project that requires just some basic tools.
Make sure you turn off your vehicle and shut all doors prior to beginning. Find the small, metal or plastic piece on the bottom of the key fob. Jiggle it until the key comes out. Then, you can insert the key into the door handle of the driver to unlock your car.
To replace the battery inside the key fob, remove the cover at the rear. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Remove the old battery and then position the new battery to ensure its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.
Once the new battery has been installed and the key fob is turned on, turn it off and on in the ignition repeatedly until the door locks. Then www.thekeylab.co.uk can test your Kia key fob and see if it is working properly again.
How to replace the smart key?
Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The difference is that the smart key comes with the small blade of a key hidden within it, whereas the standard fob doesn't. Both key fobs contain batteries that will eventually require replacement. This is an easy process that takes just two minutes.
Before you get started it is important to ensure that you're on a flat surface with enough lighting and that your Kia is off. Also, remember that there are tiny parts inside the fob that can fall out if you are not cautious.
The release button for the small size is located on the lower backside. It could be a circular button or a rectangular slot. You can open the key fob by pressing the button.
After the key fob has been opened, remove the old battery. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. Once you're done you should be able to lock, unlock and start your car using your key fob, even if the engine isn't running!
How to replace a mechanical key
The Kia key fob is a wonderful feature that lets us lock and unlock our car with the push of a button. Like any other device like a key fob, the Kia can have issues at times. There are steps to take to solve these issues and ensure that our key fobs are in good condition for the long term.
One of the most frequent problems is a dead or dead battery. This could cause the fob to stop working completely or even to stop working intermittently. If this is the issue then replace the battery with a new one.
If this isn't enough to solve the issue, you can use the flathead screwdriver that is standard to wedge the fob's casing made of plastic open. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed then replace it with a brand new one.
After the new battery has been put in, close and then open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to make sure it is working properly. If the fob isn't working, contact a locksmith or dealer to solve the issue. To avoid a lockout in the future ensure you purchase an emergency key that can work in all of the trunk and door cylinders.